Skip Headers

Oracle® Database Recovery Manager Reference
10g Release 1 (10.1)

Part Number B10770-02
Go to Documentation Home
Home
Go to Book List
Book List
Go to Table of Contents
Contents
Go to Index
Index
Go to Master Index
Master Index
Go to Feedback page
Feedback

Go to previous page
Previous
Go to current chapter
Up
Go to next page
Next
View PDF

RESET DATABASE

Syntax

reset::=

Text description of reset.gif follows


Text description of reset

Purpose

To reset the target database in the RMAN repository, which means to do either of the following actions:

Restrictions and Usage Notes

Keywords and Parameters

Syntax Element Description

TO INCARNATION primary_key

Changes the current incarnation to an older incarnation. Specify the primary key of the DBINC record for the database incarnation. Run LIST INCARNATION OF DATABASE to obtain the key. After you issue RESET DATABASE TO INCARNATION, then you can run RMAN commands such as RESTORE and RECOVER.

Examples

Resetting RMAN to a Previous Incarnation in NOCATALOG Mode: Example

In NOCATALOG mode, you must mount a control file that knows about the incarnation that you want to recover. The following scenario makes an old incarnation of database trgt current again:

CONNECT TARGET / NOCATALOG

# step 1: start and mount a control file that knows about the incarnation to which
# you want to return. if the current control file does not know about it, then
# you must restore an older control file
STARTUP NOMOUNT;
RESTORE CONTROLFILE UNTIL TIME 'SYSDATE-250';
ALTER DATABASE MOUNT;

# step 2: obtain the primary key of old incarnation
LIST INCARNATION OF DATABASE trgt;

List of Database Incarnations
DB Key  Inc Key DB Name  DB ID            STATUS   Reset SCN  Reset Time
------- ------- -------- -------------    -------  ---------- ----------
1       2       TRGT     1334358386       PARENT   154381     OCT 30 2001 16:02:12
1       116     TRGT     1334358386       CURRENT  154877     OCT 30 2001 16:37:39

# step 3: in this example, reset database to incarnation key 2
RESET DATABASE TO INCARNATION 2;

# step 4: restore and recover the database to a point before the RESETLOGS
RESTORE DATABASE UNTIL SCN 154876;
RECOVER DATABASE UNTIL SCN 154876;

# step 5: make this incarnation the current incarnation and then list incarnations:
ALTER DATABASE OPEN RESETLOGS;
LIST INCARNATION OF DATABASE trgt;

List of Database Incarnations
DB Key  Inc Key DB Name  DB ID            STATUS  Reset SCN  Reset Time
------- ------- -------- ---------------- ------- ---------- ----------
1       2       TRGT     1334358386       PARENT  154381     OCT 30 2001 16:02:12
1       116     TRGT     1334358386       PARENT  154877     OCT 30 2001 16:37:39
1       311     TRGT     1334358386       CURRENT 154877     AUG 13 2002 17:17:03
Resetting the Database After Incomplete Recovery: Example
This example assumes that 
an incomplete recovery or recovery with a backup control file was performed in NOCATALOG mode. Later, RMAN is 
started in CATALOG mode, but the RESYNC command fails because the incarnation has not been reset in the catalog.

% rman target / catalog rman/rman@catdb

Recovery Manager: Release 10.1.0.2.0 - Production

Copyright (c) 1995, 2003, Oracle.  All rights reserved.

connected to target database: TRGT (DBID=1334531173)
connected to recovery catalog database

RMAN> RESYNC CATALOG;

RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of resync command on default channel at 11/01/2001 12:00:43
RMAN-20003: target database incarnation not found in recovery catalog

RMAN> RESET DATABASE;

new incarnation of database registered in recovery catalog
starting full resync of recovery catalog
full resync complete